Showing results: 16 - 30 of 123 items found.
-
N1231A -
Keysight Technologies
The Keysight N1231A PCI Three-Axis Laser Board is a register based PCI bus board that implements three axes of laser measurement for position monitoring and closed-loop servo control. The hardware outputs, optimized for connection to a DeltaTau PMAC servo control system, provide parallel digital position data at rates up to 4MHz. The same position data along with velocity data is available over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
Innerspec Technologies, Inc
The PCI-8 is an 8-channel, PCI-based AE system on a board. Its 8 high-speed AE channels offer simultaneous AE data acquisition, waveform processing and data transfer. The board’s standard PCI form factor enables installation in standard PCs, as well as in any of Physical Acoustics’ specialized AE system chassis, while the PCI bus enables AE data transfer at speeds of up to 132 Mb/s, at a frequency range of 1 kHz to 400 kHz.
-
Dynamic Engineering
The IEEE extender card, referred to as board PWB1000281-03. Extender card to allow for testing and debugging of the chassis assembly. This board was originally an Intel design that Dynamic Engineering was authorized by Intel to re-create
-
SKU-016-XX -
Amfeltec Corp.
The PCI Express Cable Extender was designed to support the development and debugging of PCI Express boards. The PCI Express Cable Extender allows easy access from both sides of the PCI Express board that are plugged into the Extender. It has overcurrent protection and provides access to the PCI Express bus JTAG signals. By enabling access to the PCI Express bus JTAG signals, the PCI Express Cable Extender becomes a universal device that helps support the programming/loading of FPGA/CPLD during debugging and the verification PCI Express boards.
-
-
119EXT3024-37XXR -
ELMA Electronic, Inc.
VPX Test Extender 3U 240mm for conduction cooled boards in convection chassis
-
4320 -
Technobox, Inc.
Basic CMC Extender for PrPMC, PMC, and PMC-X. The Basic Common Mezzanine Card (CMC) extender provides a means to extend IEEE 1386 boards for signal accessibility. PrPMC (VITA 32), PMC (IEEE 1386.1), PMC-X (VITA 39) and any other CMC-derived board is supported.
-
119EXT3024-27XXR -
ELMA Electronic, Inc.
VPX Test Extender 3U 240mm for conduction cooled boards in conduction cooled chassis
-
PCCextend 125 -
Sycard Technology
The PCCextend 125 is a flexible extender card designed to provide easy access to a CardBus PC Card for debug or test. Designed with the same low noise characteristics of our PCCextend 140, the PCCextend 125 takes this design a step further by connecting the host and card via ribbon cables. The flexible extender consists of two PC boards—the host interface board and the card interface board. The host interface board is inserted into the host's CardBus slot.
-
CF extend 180 -
Sycard Technology
The CF extend 180 is a flexible extender card designed to provide easy access to a CompactFlash™ card for debug or test. Designed with the same low noise characteristics of our CF extend 160, the CF Extend 180 takes this design a step further by connecting the host and card via ribbon cables. The flexible extender consists of two PC boards, the host interface board and the card interface board.
-
SKU-001-0X -
Amfeltec Corp.
The 32-bit PCI Extender was designed to support the development, debugging and verification of 32-bit PCI boards. The extender provides a complete PCI debugging platform that allows easy access to logic signals; it has over-current protection, and supports hot-swap operation.
-
1940000519-0000R -
ELMA Electronic, Inc.
3U VPX Extender for convection cooled boards in convection cooled chassis VITA 67.1 (VITA67 connectors not included)
-
1940000519-9001R -
ELMA Electronic, Inc.
3U VPX Extender for conduction cooled boards in conduction cooled chassis VITA 67.1 (VITA67 connectors not included)
-
SKU-006-01 -
Amfeltec Corp.
The x1 PCI Express Extender was designed to support the development, debugging and verification of PCI Express boards. The Extender provides a complete PCI Express debugging platform that allows easy access to the logic signals, it has overcurrent protection and hot-swap operation capability.
-
3690-2 -
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.